ServicesRemodel & Addition Wiring
Remodel & Addition Wiring in Hudson Oaks
A new kitchen, bath or addition asks more of your electrical system than the old layout did. We plan the new circuits, check the wiring they connect to and install everything cleanly behind the walls, so the new rooms and the existing house work well together.
New Rooms, Connected to a System That Can Carry Them
A remodel changes how much power part of your home draws, and where. A new kitchen adds dedicated circuits for the range, dishwasher and microwave. A primary suite brings bathroom outlet protection, layered lighting and sometimes a heated floor. We design and install that wiring, then tie it into the system you already have.
Before anything new goes in, we look at what it will lean on: open space in the panel, the condition of breakers and terminations, and the older circuits that will keep running beside the new ones. Sound wiring stays. If a circuit feeding the remodeled space is overloaded or its insulation has gone brittle, we show you what we found and explain the choice.
We work directly with you or alongside your general contractor, and we fit rough-in and finish work around the other trades.
What We Handle on Your Project
A load check and a circuit layout
We total what the new space will use and measure it against your panel's capacity. Before any work, you get a written layout marking every new circuit, outlet and fixture.
Rough-in with the framing exposed
New cable is pulled, boxes are set at the correct heights, and runs are stapled and protected as code requires. We bore framing cleanly and seal holes that pass between spaces.
Circuits for kitchens and baths
Appliances get their own circuits, countertop outlets are spaced to code, and GFCI and AFCI protection goes where required. Exhaust fans and under-cabinet lights are wired in the same pass.
Power for an addition
Bigger additions usually need a subpanel or a new feeder from the main panel. When the main panel is close to its limit, we go over the options on our Panel Upgrades page with you.
Trim-out, labels and cleanup
Once drywall and paint are done, we put in devices, plates and fixtures, test each circuit and update the panel directory so every breaker is marked. Dust and scraps leave with us.
Signs Your Project Needs Electrical Planning
You are redoing a kitchen or bath
These rooms carry the heaviest loads and the strictest code requirements. Planning the circuits early keeps the cabinet and tile layout from being reworked later.
You are adding square footage
An addition, a garage conversion or an enclosed patio needs its own lighting, outlets and often its own heating and cooling circuit.
The panel is already full
No open breaker spaces, or tandem breakers squeezed in to make room, usually means the panel needs attention before new circuits can be added safely.
Breakers trip when old and new loads overlap
If a temporary setup or an earlier remodel trips breakers when the microwave and space heater run together, the circuit layout needs rethinking.
An inspector flagged the rough-in
If another crew's work did not pass, we can review the notes and correct it. Our Code Corrections & Inspection Fixes page covers that work in more detail.
The Steps of Wiring a Remodel
- 1
Site visit and layout
We come out, review the plans or the room, open the panel and test the circuits that will serve the remodel. Together we mark where outlets, switches and fixtures will go.
- 2
Scope on paper and permit filed
You get the electrical work itemized line by line. We file the permit and book inspections as the local jurisdiction requires.
- 3
Rough wiring
While the framing is open, we pull cable, mount boxes and make connections, keeping nearby floors and finished areas covered.
- 4
Rough-in inspection
The inspector reviews the wiring before insulation and drywall go in. If changes are needed, we make them and schedule the re-inspection.
- 5
Trim-out and walkthrough
After the walls are done, we set devices and fixtures, test every circuit, pass the final inspection and show you the updated panel.
What Shapes the Cost
Every remodel is priced from its own scope, so we quote after the walkthrough rather than from a rate sheet. The written estimate lists each part of the job, and if something hidden turns up once walls open, we show you before any change in price.
- Size and circuit count
- A bathroom refresh may need two or three circuits. A full kitchen or a large addition can need many more, plus a subpanel.
- Panel capacity
- If the existing panel has room and capacity, the job is simpler. If it does not, a subpanel or panel upgrade becomes part of the scope.
- Access to the framing
- Open walls during a gut remodel are quicker to wire than fishing cable through finished drywall. Long attic runs also take more time, especially in the heat of a North Texas summer.
- Fixtures and devices you choose
- Recessed lighting, dimmers, smart switches and under-cabinet strips each add materials and labor compared with basic devices.
- Condition of existing wiring
- Older circuits that will carry the new rooms may need repair or replacement before the new work ties in.
Questions About Wiring a Remodel or Addition
Something not covered here? (682) 319-2260
Will you get the electrical permit for the remodel?
Yes. We file the permit and book the rough and final inspections your local jurisdiction requires, so you never have to visit the permit office for the electrical side.
Can my existing panel carry a new kitchen or addition?
Some panels can, and some are already near their limit. We run a load calculation at the walkthrough and tell you straight which one you have. If you need more capacity, we explain whether a subpanel or a panel upgrade suits your home better.
Do you work alongside general contractors?
Yes. We time our rough-in with the framing, plumbing and HVAC crews and return for finish work after drywall and paint. On smaller jobs, we are glad to work with you directly.
Is it worth replacing old wiring while the walls are open?
Often it is, because reaching the wiring is the hardest part of a rewire. We test the circuits around the remodel and tell you which ones should stay. If aging wiring runs through much of the house, we may recommend whole-home rewiring as its own project.
How long will the electrical part take?
That depends on the size of the space and the other trades' schedules. One bathroom roughs in far faster than an addition with several rooms. You get a realistic timeline at the walkthrough, and we update you as inspections get scheduled.
Will you take a remodel outside Hudson Oaks?
Yes. We wire remodels and additions in Weatherford, Willow Park, Aledo, Annetta and other towns nearby, following the permit process in each jurisdiction.
Bring Us In Before the Drywall Goes Up
The best time to plan the wiring is while the design is still on paper. We will look at your existing system, map the new circuits and give you a clear written scope.